Difference between revisions of "PCB Repair Logs Bombjack Bootleg"
m |
m |
||
| Line 19: | Line 19: | ||
'''Forum Thread:''' [http://www.aussiearcade.com.au/showthread.php/30208-Bomb-Jack-Repair-Log Bombjack (Bootleg) PCB Repair]<br> | '''Forum Thread:''' [http://www.aussiearcade.com.au/showthread.php/30208-Bomb-Jack-Repair-Log Bombjack (Bootleg) PCB Repair]<br> | ||
<br> | <br> | ||
Received an "untested" Bomb Jack board from ebay. | |||
It appears to be a bootleg/original hybrid. The A board was a bootleg, the one with only 2 x AY-3-8910's on it and the B board is from an original. | |||
'''Problem:''' Missing the green and blue colours and sound was stuck in a constant repeating loop from power up.<br> | |||
'''Fix:''' The RGB, sync and video ground go to a 5 pin header on this bootleg, not a 6 pin header, the previous owner was clearly not had an adapter or plug for anything on this board and had soldered the wires directly on, had also melted all the plastic supporting these 5 pins so a couple were shorting to ground, easy fix. | |||
The sound had a corrupt EPROM, I erased and burnt a new one, still no change. | |||
The RAM had already been socketed so I tested it and it came up clear. Checked the Z80 with the logic probe and found the address lines were all high except for a couple that were pulsing. | |||
Desoldered it and tested it, it failed on pretty much everything, replaced it and now the sound was working but seemed to be lagging behind when compared to MAME. | |||
After much head scratching and some very bad words I tested the RAM again on a continuous cycle in the ChipMaster tester, whislt it was testing I put in a new one so I could continue testing the board and fault fixed! Swapped the RAM back and fault is back. This RAM works fine in my other boards so am putting it down to RAM speed. | |||
<br>[[PCB_Repair_Index|Back to PCB Repair Index]] | <br>[[PCB_Repair_Index|Back to PCB Repair Index]] | ||
Latest revision as of 07:48, 23 August 2012
Bombjack (Bootleg)
 |
|
| PCB Image | Reserved |
|---|---|
| Pin Out | Reserved |
Repairer: porchy
Forum Thread: Bombjack (Bootleg) PCB Repair
Received an "untested" Bomb Jack board from ebay.
It appears to be a bootleg/original hybrid. The A board was a bootleg, the one with only 2 x AY-3-8910's on it and the B board is from an original.
Problem: Missing the green and blue colours and sound was stuck in a constant repeating loop from power up.
Fix: The RGB, sync and video ground go to a 5 pin header on this bootleg, not a 6 pin header, the previous owner was clearly not had an adapter or plug for anything on this board and had soldered the wires directly on, had also melted all the plastic supporting these 5 pins so a couple were shorting to ground, easy fix.
The sound had a corrupt EPROM, I erased and burnt a new one, still no change.
The RAM had already been socketed so I tested it and it came up clear. Checked the Z80 with the logic probe and found the address lines were all high except for a couple that were pulsing.
Desoldered it and tested it, it failed on pretty much everything, replaced it and now the sound was working but seemed to be lagging behind when compared to MAME.
After much head scratching and some very bad words I tested the RAM again on a continuous cycle in the ChipMaster tester, whislt it was testing I put in a new one so I could continue testing the board and fault fixed! Swapped the RAM back and fault is back. This RAM works fine in my other boards so am putting it down to RAM speed.
