Difference between revisions of "PCB Repair Logs 1942"
(Created page with "==1942== <p><table class="infobox vevent" style="width:22em;" cellspacing="5"> <caption class="summary" style=""><b>1942</b></caption> <tr class="> <td colspan="2" class="" s...") |
m |
||
Line 19: | Line 19: | ||
'''Forum Thread:''' [http://www.aussiearcade.com.au/showthread.php/23417-1942-Repair-Log 1942 PCB Repair]<br> | '''Forum Thread:''' [http://www.aussiearcade.com.au/showthread.php/23417-1942-Repair-Log 1942 PCB Repair]<br> | ||
<br> | <br> | ||
'''Symptom:''' Background graphics corrupted – tiles are being duplicated vertically in approx. 1 inch rows<br> | |||
'''Cure:''' Pin 11 of LS86 at 10J stuck low (on the lower board) - replaced<br> | |||
<br> | |||
'''Symptom:''' board is ‘dead’, garbage *briefly* on screen on power on but then screen goes blank. Setting Test Mode on gives a static screen of garbage but won’t run any tests.<br> | |||
'''Diagnosis:''' Checked all EPROMs – okay. Checked all RAM – okay. Used a logic probe on the 74LS138 at 10L and found that pin 10 was floating and pins 11, 12 and 13 were all High (should be Pulsing). Tried piggy-backing a 74LS138 onto the same IC at 10L, and the board fired right up.<br> | |||
'''Cure:''' Socketed and replaced 74LS138 at 10L<br> | |||
<br> | |||
'''Symptom:''' When board was cold, on power up the ‘bar’ near the bottom of the screen would sometimes glitch with garbage characters appearing over it. This stopped glitching after a few seconds, and during gameplay there were hardly any noticeable glitches.<br> | |||
'''Diagnosis:''' Determined that the two 2114’s at 9H and 10H on board 2 were responsible for the onscreen sprites, so tried piggy-backing good 2114’s onto them one at a time. Found that the 2114 at 10H was suspect<br> | |||
'''Cure:''' Socketed and replaced 2114 at 10H<br> | |||
<br> | |||
'''Symptom:''' Board booting up but won’t coin up, etc and resets when trying to run attract mode<br> | |||
'''Cure:''' Bad 6116/TMM2016 at location A9 ? (chip nearest ROMs) on CPU board<br> | |||
<br> | |||
'''Symptom:''' Sprites replaced by random bits of other sprites<br> | |||
'''Cure:''' Bad 2114 RAM at location H10 on video board<br> | |||
<br> | |||
'''Symptom:''' Sprites mis-positioned and broken up<br> | |||
'''Cure:''' Bad 2114 RAM at location H9 on video board<br> | |||
<br> | |||
'''Symptom:''' No background displayed<br> | |||
'''Cure:''' Bad LS138 at E11 (near edge connector on top board) where pin 14 goes to pin 1 of the Ls377 at location A8 (just below the 6 (or 3) background graphics EPROMs on the lower board<br> | |||
<br> | |||
'''Symptom:''' Dotted lines across parts of the screen<br> | |||
'''Cure:''' Bad 2148/6148 at location F2<br> | |||
<br> | |||
'''Symptom:''' Boardset powers on and plays okay, all graphics okay BUT random garbage text present in many areas<br> | |||
'''Cure:''' Bad LS367 at location H1 on the CPU board<br> | |||
<br> | |||
'''Symptom:''' No sound, just a hiss. No input to sound amp (Capcom original, top board)<br> | |||
'''Cure:''' Bad outputs on LS138 at E9 – replaced<br> | |||
<br> | |||
'''Problem:''' Text corrupting, appearing in the wrong places, etc (Capcom original top board)<br> | |||
'''Cure:''' All outputs on the LS157 at E1 stuck low – replaced<br> | |||
<br> | |||
'''Symptom:''' All sprites extremely blocky and unrecognisable<br> | |||
'''Diagnosis:''' Checked the 6 sprite EPROMs on the lower board and then the chips around them – found that pin 9 on the four LS194’s was ‘dead’. Traced this back to the top board where it was found that all the outputs on the LS74 at location K8 were dead<br> | |||
'''Cure:''' Replaced faulty LS74 at location K8<br> | |||
<br> | |||
<br>[[PCB_Repair_Index|Back to PCB Repair Index]] | <br>[[PCB_Repair_Index|Back to PCB Repair Index]] |
Revision as of 13:30, 20 August 2012
1942
PCB Image | Reserved |
---|---|
Pin Out | Reserved |
Repairer: VectorGlow
Forum Thread: 1942 PCB Repair
Symptom: Background graphics corrupted – tiles are being duplicated vertically in approx. 1 inch rows
Cure: Pin 11 of LS86 at 10J stuck low (on the lower board) - replaced
Symptom: board is ‘dead’, garbage *briefly* on screen on power on but then screen goes blank. Setting Test Mode on gives a static screen of garbage but won’t run any tests.
Diagnosis: Checked all EPROMs – okay. Checked all RAM – okay. Used a logic probe on the 74LS138 at 10L and found that pin 10 was floating and pins 11, 12 and 13 were all High (should be Pulsing). Tried piggy-backing a 74LS138 onto the same IC at 10L, and the board fired right up.
Cure: Socketed and replaced 74LS138 at 10L
Symptom: When board was cold, on power up the ‘bar’ near the bottom of the screen would sometimes glitch with garbage characters appearing over it. This stopped glitching after a few seconds, and during gameplay there were hardly any noticeable glitches.
Diagnosis: Determined that the two 2114’s at 9H and 10H on board 2 were responsible for the onscreen sprites, so tried piggy-backing good 2114’s onto them one at a time. Found that the 2114 at 10H was suspect
Cure: Socketed and replaced 2114 at 10H
Symptom: Board booting up but won’t coin up, etc and resets when trying to run attract mode
Cure: Bad 6116/TMM2016 at location A9 ? (chip nearest ROMs) on CPU board
Symptom: Sprites replaced by random bits of other sprites
Cure: Bad 2114 RAM at location H10 on video board
Symptom: Sprites mis-positioned and broken up
Cure: Bad 2114 RAM at location H9 on video board
Symptom: No background displayed
Cure: Bad LS138 at E11 (near edge connector on top board) where pin 14 goes to pin 1 of the Ls377 at location A8 (just below the 6 (or 3) background graphics EPROMs on the lower board
Symptom: Dotted lines across parts of the screen
Cure: Bad 2148/6148 at location F2
Symptom: Boardset powers on and plays okay, all graphics okay BUT random garbage text present in many areas
Cure: Bad LS367 at location H1 on the CPU board
Symptom: No sound, just a hiss. No input to sound amp (Capcom original, top board)
Cure: Bad outputs on LS138 at E9 – replaced
Problem: Text corrupting, appearing in the wrong places, etc (Capcom original top board)
Cure: All outputs on the LS157 at E1 stuck low – replaced
Symptom: All sprites extremely blocky and unrecognisable
Diagnosis: Checked the 6 sprite EPROMs on the lower board and then the chips around them – found that pin 9 on the four LS194’s was ‘dead’. Traced this back to the top board where it was found that all the outputs on the LS74 at location K8 were dead
Cure: Replaced faulty LS74 at location K8